Craftsman 113.198410 Uživatelský manuál

ISave This ManualFor Future Reference gJ _A/ SownersmonuolMODEL NO.113.19841010" DELUXEELECTRONICRADIAL SAW WITH44" CABINET AND2 DOORSORt13.

contentsPageGuarantee ... 2General Safety Instructions for Power Tools ... 2Additional Safety Instructions for Radia

unpacking and preassemblyWARNING: TO AVOID INJURY FROM UNEXPECT-ED STARTING OR ELECTRICAL SHOCK, DO NOTPLUG THE POWER CORD INTO A SOURCE OFPOWER. THIS

44" CABINET ASSEMBLYFOR MODEL NO. 113.198610ASSEMBLE CABINET BEFOREMOUNTING SAW1. Separate all "loose" parts from packing materialsand

CASTER/FOOT ASSEMBLY NO. 50753____8A R.H. Foot Assembly ... 1B L.H. Foot Assembly ... 1C Caster ...

8. Locate the right and left foot assemblies, two (2)leveling feet, two (2) 1/2-13 hex nuts, the rightand left side panels, and four (4) 1/4-20 x 7/16

11.Securerearof lowershelfto rightsideandleftsidepanelsusingtwo (2)1/4-20x 1/2trussheadbolts,Iockwashersand hexnuts. Handtightennutsonlyatthistime.12.

CHECKING CABINET FOR SQUARENESSTOOLS NEEDED: Framing square, 3/4" wrench and7/16" wrench or socket.1. With cabinet on back side place a squa

INSTALLING DRAWERSFOR MODEL NO. 113.198610Tools needed: 7/16" wrench or socket, mediumscrewdriver.1. Locate one (1) front support, one (1) uppers

6. Locate the twelve (12) stand slide brackets,twenty-four (24) truss head bolts, Iockwashersand hex nuts. Assemble the stand slide bracketson the rea

44" CABINET ASSEMBLYFOR MODEL NO. 113.198410ASSEMBLE CABINET BEFOREMOUNTING SAWSeparate all "loose" parts from packing materialsand che

FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL SAWIf within one year from the date of purchase, this Craftsman Radial Saw fails due to a defect in materia

2.Afterlayoutofstandparts,takethebottomshelfandturnupsidedownonfloor.Smallfrontflangeshouldbepointingupward.3. Place one shelf stiffener against front

8. Locate the right and left side panels and eight (8)1/4-20 x 1/2 truss head bolts, Iockwashers andhex nuts to attach side panels to shelf. Mount the

CHECKING CABINET FOR SQUARENESSTOOLS NEEDED: Framing square, 3/4" wrenchand 7/16" wrench or socket.1. With cabinet on back side place a squa

MOUNTING DOORS FORMODEL NO. 113.1984101. Slide the upper support into the top of the centersupport so the top and side holes line up. Thenassemble to

MOUNTING SAW1. From loose parts bag #488, find the followinghardware:8 - Truss Head Bolts 1/4-20 x 1/28 - Lockwashers External 1/48- Hex Nuts 1/4-202.

Attach Elevation Handwheel1. From loose parts bag, find one (1) screw 10-32 x1/2 and one (1) external Iockwasher. Installhandwheel to front of base as

ALIGNMENT PROCEDUREIMPORTANT: In order to obtain maximum cuttingaccuracy and safety, the following six steps must becarefully followed. Become thoroug

6. Lay the arbor wrench on the work tableunderthemotor shaft. Carefully lower the arm with theelevation handle until the motor shaft is justtouching t

Adjusting front table lock handlesWARNING: TO AVOID SUDDEN SLIPPAGE,BREAKAGE, OR THROWING OF PARTS, FRONTTABLE BOARD LOCK HANDLE MUST LOCKTABLE BOARDS

(c) Carefully retighten uppertwo (2) 1/4-20 socketset screws alternating from left side to rightside so as not to force arm out of adjustment.(d) Rech

additionalBEFORE USING THE SAW:instructions for radialarm saws.e..d3 =€_e--WARNING: TO AVOID MISTAKES THAT COULDRESULT IN SERIOUS, PERMANENT INJURY, D

STEP FIVESquaring Blade to Rip FenceNOTE: If alignment procedure steps three and fourwere not performed, this adjustment step cannot beaccomplished. T

a.b,Unlock the bevel lock handle and loosen thetwo cap screws located thru the rear of themotor support (see illustration). A 1/8" hex "L&qu

location and function of the electronic indicator systemBATTERY STORAGECOMPARTMENT(ON SIDE)ELECTRONIC MEASUREMENTTO LOCK REMOVE YELLOW KEYFUNCTION IND

1. Installing the BatteryInstall the battery into the compartment as shown.The bottom rear tab of the battery should be heldinside the compartment by

d.Loosen the miter angle encoder mountingbracket by backing the mounting screws offuntil the encoder will rotate slightly on thecolumn tube.e. Rotate

f. If the adjustment will not align the displayreadout to the bevel index positions, refer tothe trouble shooting guide in this manualg. When the enco

location and function of controlsWARNING: FOR YOUR OWN SAFETY ALWAYSLOCK THE SWITCH "OFF" WHEN SAW IS NOT INUSE. REMOVE KEY AND KEEP IT IN A

Depth of Cut (Elevation)a. The diagram shows the elevation crank whichis used to raise and lower the saw blade.b. Clockwise rotation raises the blade

5. Blade Angle (Bevel)a. A single bevel lock handle is used in angularpositioning and indexing of the motor, toprovide the desired saw blade (bevel) a

8. Blade Guard and Anti-Kickback/SpreaderAssembly- Positioningfor Ripping.WARNING:NEVERPOSITIONTHE GUARDORANTI-KICKBACK/SPREADERASSEMBLYWITHTHESAWRUNN

while the cutting tool is rotating. The rotatingtool could cut and throw anything hitting theblade causing the saw to unexpectedly comeforward.-- Use

basic saw operationWARNING: TO AVOID MISTAKES THAT COULDCAUSE SERIOUS PERMANENT INJURY, OBSERVEALL THE FOLLOWING INSTRUCTIONS IN ADDI-TION TO THOSE ON

2. Make sure the arbor nut is snug.3. Clamp the guard in a horizontal position.4. Lock the swivel lock handle. Make sure it is firmlylocked. (See page

rectangular frame. The radial arm is set to a desiredangle of cut, swivel and bevel settings at 0° andlocked. The workpiece being cut is positioned an

board against the fence must be straight and willnot catch on kerfs in the fence- for workpiecesthicker than the fence is high, install a higherfence

OPERATION NO. 5 -OUT-RIPPING AND IN-RIPPING1. Ripping is the process of sawing the workpiecealong its length by feeding it into the sawbladewhen using

OPERATION NO. 6- BEVEL RIPPINGBevel ripping is either in-ripping or out-ripping asdescribed above, except the saw blade is tilted out ofperpendicular

AUXILIARYFENCEFORMOLDINGTo use the molding head with the arm in the 0 °crosscut position an auxiliary fence must be used.WARNING: IF THE AUXILIARY FEN

5. Adjustment is complete when both locking andindexing functions are working properly. Replacemotor support cover.ADJUSTING SWIVEL LOCK HANDLEThis ha

ADJUSTINGCARRIAGEBEARINGSThe carriage should roll freely but with some resist-ance for the entire length of travel. To test forbearing looseness, perf

2. With a 3/16 inch hex "L" wrench find the 1/4-20hex socket cap screw through the hole in the reararm cover. To tighten turn the wrench clo

fromthenoseside(oppositethesawdustexhaustchute)of the guard. Note the warningon theguard.-- Toavoidinjuryfromthrownpieces,slips,orjams,theworkpiecemus

trouble-shootingHAVE YOU FOLLOWED ALL SIX STEPS OFTHE ALIGNMENT PROCEDURE? IF YOUHAVE NOT FOLLOWED THEM IN THEIRPROPER SEQUENCE, YOU CANNOTEXPECT A CC

1. RADIAL SAW DOES NOT MAKE ACCURATE 0°or 45° MITER CROSSCUTS.a. Looseness between column tube and columnsupport.Align as described in Alignment Proce

4. SAW KERF (CUT EDGE) OF STOCK ROUGH-TOOTH MARKS LEFT ON EDGE OF SAWKERF.NOTE: This condition is commonly called "HEEL".a, Crosscutting or

9. CLAMPING FORCE NOT SUFFICIENT ATMITER ANGLES OTHER THAN 45 °.a, Miter Lock Handle requires Adjustment.Refer to Adjusting Miter Lock Handle in Adjus

TROUBLE SHOOTING GUIDE - ELECTRONICSPROB'EM]No display whenis pressed.PROBABLE CAUSE1. Battery incorrectlyinstalled.'2. Battery contacts dir

MOTOR TROUBLE-SHOOTING CHARTNOTE: Motors used on wood-working tools areparticularly susceptible to the accumulation ofsawdust and wood chips and shoul

maintenance and lubricationMAINTENANCEWARNING: FOR YOUR OWN SAFETY, TURNPOWER SWITCH "OFF'AND REMOVE PLUG FROMPOWER SOURCE OUTLET BEFORE MAI

A light film of oil should be wiped on the face of thecolumn tube to lubricate the fit between the columntube and column support. With elevation crank

repair partsPARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113,198410 and 113.19861010(SEE FIG, 6)136 iJ33/2225262827(SEE FIG. 2)30

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610Always order by Part Number - Not by Key NumberFIGURE 1Key

provide additional guarding from contact with thefront of the blade.--To prevent the cutting tool from grabbing thetable or workpiece and being propel

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.1986106J%14O1234173O188 _ !120162122\\14 "19>28292728 46J

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610Always order by Part Number - Not by Key NumberFIGURE 2 - B

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.1986106I311389// 1o/111213\142220J 29 28%2718334/2524FIGURE 362

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610Always order by Part Number - Not by Key NumberFIGURE 3 - Y

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610217\3 4918192317/39382927/FIGURE 464

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610Always order by Part Number - Not by Key NumberFIGURE 4 - Y

!KeyNo.661234567891011121314PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610Always order by Part Number - N

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610Always order by Part Number - Not by Key Number1FIGURE 6 -

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113,198410 and 113.198610Always order by Part Number - Not by Key Number]FIGURE 7 -

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610Always order by Part Number - Not by Key Number475\112 9 91

OutripPositioningthebladeparallelto thefencewiththemotortowardthe rearof the sawproducingmaxi-mumrippingcapacity.Seeillustrationonpage42.PushStickA de

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610gJ/\\!/70

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610Always order by Part Number - Not by Key Number50u. _.z0303

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610/214 3/;4_1919195 4181019\//iI /L //'/FIGURE 1072

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113,198610Always order by Part Number - Not by Key NumberFIGURE 10 -

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAWMODEL NOS. 113.198410 and 113.198610Always order by Part Number - Not by Key Number3\\FIGURE 11

NOTES75

r -_ FownersmanualSERVICEMODEL NO.113.19841010" DELUXEELECTRONICRADIAL SAW WITH44" CABINET AND2 DOORSOR113.19861010" DELUXEELECTRONICRA

It is recommended that you have a qualified electri-cian replace the two prong outlet with a properlygrounded three prong outlet.An adapter as shown b

1. If the protector opens the line and stops the sawmotor, immediately turn the saw switch "OFF",remove the key and allow motor time to cool