Craftsman 113.234650 Uživatelský manuál

f'_ Save ThisManualFor Future Referenceowner'smanualMODEL NO.113.234650I 0" CONTRACTORMITER SAWSerialNumberModel and serial numbersmay

Step Two--Checking and Aligning Blade with TurnTable Slot1. The blade should look like it's parallel to the sidesof the turn table slot. The blad

Step Four--Pivot AdjustmentsNOTE: These adjustments were made at the factoryand normally do not require readjustment.1. The miter saw should rise comp

Fence PositionsThe miter saw has two fence positions. The front fenceposition is used for workpieces up to standard 2 x 4 for.-',Jtoff and bevel

NOTE: Pay attention to pieces removed, noting theirposition and direction they face (see illustration). Wipethe blade collars clean of any sawdust bef

If the saw _sto be used naportabteapplicaton, mounthe saw to a _" piece of plywood The mour'tm 9 boardcan then be clamped down Io prevent ,t

FRONTSIDE0 00IIoII00I i0o oIIC_oQmoo o o o10 ¸.I14' ,IAttach mounting board to holes indicatedCATALOG NO. 9-22244 LEG SETBASIC SAW OPERATIONSWARN

7. Never cut FREEHAND:a. Brace your workpiece solidly against the fenceand table top so it will not rock or twist duringthe cut. Make sure there is no

Miter CutWhen a miter cut is required, move the saw to thedesired angle. Do not stand in front of the saw table.Move with the handle to the miter angl

Compound CutWhen a compound cut is required, select the correctbevel and miter position. Move with the handle to themiter angle to make the cut. If th

Workpiece SupportLong pieces need extra supports. The supports shouldbe placed along the workpiece so the workpiece doesnot sag and your hand holding

FULL ONE YEAR WARRANTY ON CRAFTSMAN MITER SAWIf within one year from the date of purchase, this Craftsman Miter Saw fails due to a defectin material o

Filler Blocks for Cutting Crown MoldingsThe majority of crown moldings have contact surfacesof 52 ° and 38 to the rear surface of the molding. Whenjoi

maintenance and lubricationMaintenanceAlways unplug the power cord before any maintenancecheck on this saw.DANGER: Never put lubricants on the blade w

PROBLEMBrake does not stopblade within2-5 seconds.Motor does not start.Brush sparking whenswitch released.TROUBLE SHOOTING GUIDE - MOTOR2,PROBABLE CAU

WHITEBLACKif'TRIGGERSWITCHi,.vBRUSHSHORT BLUELONG_'_ BLUE _BRAKEBRUSHCIRCUIT DIAGRAMNOTES23/

PARTS LIST FOR CRAFTSMAN 10 _'COMPOUND MITER SAWMODEL NO. 113.23465024

repair partsPARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113.234650Always order by Part Number--Not by Key NumberFIGURE 1KeyNo.PartNo

repair partsPARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113.23465021e23 222 1I14181,/1615%117\8; ;lil_12Always order by Part Number-

repair partsPARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113,2346501011/1217Always order by Part Number--Not by Key NumberFIGURE 3--P

repair partsPARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113.2346502319181716152O2122t1410 9 ..._...3413111211/

repair partsPARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO, 113.234650Always order by Part Number--Not by Key NumberFIGURE 4, Blade &

additional safety instructions for miter sawSafety is a combination of common sense, staying alertand knowing how your miter saw works.BEFORE USING TH

NOTES30i

NOTES31

fowner'smanualSERVICEMODEL NO.113.234650I 0" CONTRACTORMITER SAWHOW TO ORDERREPAIRPARTS10-1NCH CONTRACTORMITER SAWNow that you have purchase

10. Never cut more than one workpiece at a time,11. Make sure the cut off piece can move side-ways after it's cut off, Otherwise, it couldget wed

Revolutions Per Minute (RPM)The number of turns completed by a spinning object inone minute.Sawblade PathThe area of the workpiece or table top direct

the load and the suppy c_rcu_t whenever motordoesnt work well Check wire s_zes and length withthe Wire Size Chart belowWIRE SIZESThe use of any extens

tools neededTools required for assembly and alignment:• Medium Screwdriver• #2 Phillips Screwdriver• Combination Square• '_ Box End/Open End Wren

knowing your miter saw1. Warning label,2. Handle Latch--The miter saw can be locked in thelowered position for compact storage.3. Fence Lock Handles--

assembly and alignmentASSEMBLY AND ALIGNMENTAssembling the Lower Blade GuardNOTE: For compact shipment the lower blade guardhas been partially disconn