Craftsman 113.23161 Uživatelský manuál

SearsownersmanualMODEL NO.113.23161SerialNumberModel and serialnumber may be foundat the front of the base.You should record bothmodel and serial numb

assembly and adjustmentsd. Place the large, front table board on the tablesupports.e. Align the counterbored holes with matching holes intable support

3.Squaring the Crosscut Travel.a. Check to make sure the arm latch handle is securelylatched in the detent and the arm lock handle is stilltight.b Ins

assembly and adjustmentse. After the crosscut travel has been accuratelysquared, check the 0° position on the indicator scaleof the radial arm cap to

b. Sight (visually) to check for proper alignment ofspreader with saw blade as shown. If the spreader isnot aligned, adjust it as follows:(1) Loosen t

operating controls6. "Power Switch and Key". This ON-OFF switch (12) islocated in the upper left-hand area of the carriage and isa red color

Spreaderto prevent kerf from closing in on sawblade andpossible Mckback,- to prevent "wrong-way feed". "Wrong-way feed" isfeeding

basic saw operations3. Tighten the carnage lock knob.CAUTION: Before making the cut, make sure the armlatch handle is fully engaged in the detent notc

OPERATION NO. 4 - COMPOUND CROSSCUTCompound crosscutting is the combination of miter andbevel crosscuts. The radial arm and bevel are set to produceth

basic saw operationsOPERATION NO. 6- BEVEL RIPPINGBevel ripping Is either in-ripping or out-ripping as describedin preceding instructions, except the

An adapter as shown below is available for connecting plugsto 2-prong receptacles. The green grounding lug extendingfrom the adapter must be connected

FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL SAWSIf within one year from the date of purchase, this Craftsman Radtal Saw fails due to a defect in materi

trouble-shootingTROUBLE-SHOOTINGEven though the finest materials and precisionworkmanship have been incorporated into your Craftsmansaw, it is reasona

h. Adjustingthearmlatchhandleto correctcrosscuttravel.In some remote cases, due to rough handling, etc.,the crosscut travel cannot be squared by the u

trouble-shooting(b)While holding the motor with one hand andthe square with the other hand, tilt themotor until saw blade is square with tabletop. The

3. Blade Heels to the Right or Left."Heeling" is a term used to describe a condition wherethe saw blade is not aligned with the direction in

trouble-shootingf.Adjusting to Eliminate Heel(1) Remove the left-hand carriage cover by removingthe two attaching screws.(2) Loosen the yoke clamp han

6. SawBladeContinuesto "Coast" Even With FingerForce Applied to Manual Brake Button.a. Oil or grease on brake drum or brake button (shoe).Re

trouble-shootingTROUBLE SHOOTINGNOTE: Motors used on wood-working toolsare particularly susceptible to theaccumulation of sawdust and wood chipsCHART-

17 j 16 115 14Key PartNo. No. DescriptionPARTS LIST FOR CRAFTSMAN IO-INCH RADIAL SAWMODEL NUMBER 113.23161FIGURE 1 - GUARD ASSEMBLY1 635372 635413 635

€lo27<_ 28 6l 25 2426SEE FIG. 6I FOR EXPLODED ",,;IE,qFigure 2PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL SAWMODEL NUMBER 113.23161tSEE FIG 4FOR E

PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL SAWMODEL NUMBER 113.23161FIGURE 2Key PartNo. No. Description12345678910111213141519123OSTD 5512256318330613STD

additional safety instructions for radial sawsWARNING: DO NOT CONNECT POWER CORD UNTILTHE FOLLOWING STEPS HAVE BEENSATISFACTORI LY COMPLETED:A. Assemb

oQme!3Q49 4847 46/ _ 31 32 / 33 3429 30 //-'_-_ 2938Figure 3f3511 12\1:'37

PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL SAWMODEL NUMBER 113.23161FIGURE 3Key PartNo. No. Description1 STD 60080523630156OO524 STD 5412315 STD 5511316

222511 10 9jlPARTS LIST FOR CRAFTSMAN 10-INCH RADIAL SAWMODEL NUMBER 113,2316118/19J24Figure 4"13Qlit"13QU'J

PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL SAWMODEL NUMBER 113.23161FIGURE 4Key PartNo. No. Description123456789101112131415166352363586STD 5O2505STD 522

wANY ATTEMPT TO REPAIR THIS MOTORMAY CREATE A HAZARD UNLESS REPAIR ISDONE BY A QUALIFIED SERVICE TECHNICIAN.REPAIR SERVICE IS AVAILABLE AT YOURNEAREST

PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL SAWMODEL NUMBER 113.23161!25 88FIGURE 6Key PartNo. No. Description- 631831 630512 635843 630534 6305456 STD 57

SearsownersmanualSERVICEMODEL NO.113.23161HOW TO ORDERREPAIR PARTSIO-INCH RADIAL SAWNow that you have purchased your 10-inch radial saw, should aneed

additional safety instructions for radial saws6. Prowde proper support for the workptece, based on itsslzf and the type of operation to be performed.

unpacking and pre-assemblyCONTENTSPageSafety Instructions ... 2,3,4 & 5Unpacking and Pre-Assembly ... 5Assem

assembly and adjustments3. Installing Motor and Carriage Assembly on Radial Arm.a.b.ARM LOCI'Rotate the elevation crank counterclockwiseapproxima

C._,RR[&OE CO..'ER _k H )CARRIAGELOCK SHOEhi.Install the carriage stop screw and Iockwasher.Install the carriage lock shoe and carriage lock

assembly and adjustmentsALIGNMENT INSTRUCTIONS1. Adjusting Table Supports Parallel to Radial Arm.a. Loosen the guard clamp screw and remove theguard.b

k.Move the carriage out near the end of radial arm andmove the arm until the end of motor shaft is overthe table support above the front support attac